On 6/13/16, Andreas Reschke <arm_ml@xxxxxxxxxxx> wrote: > Am 13.06.2016 um 17:50 schrieb Fabien Blanchet: >> Le 13/06/2016 à 17:32, ali hagigat a écrit : >>> On 6/13/16, Peter Robinson <pbrobinson@xxxxxxxxx> wrote: >>>> none using an >>>> >>>> On Mon, Jun 13, 2016 at 2:29 PM, ali hagigat <hagigatali@xxxxxxxxx> >>>> wrote: >>>>> On 6/13/16, Peter Robinson <pbrobinson@xxxxxxxxx> wrote: >>>>>> On Mon, Jun 13, 2016 at 11:34 AM, ali hagigat <hagigatali@xxxxxxxxx> >>>>>> wrote: >>>>>>> I want to use the Fedora 23 image with Odroid, XU4/3. >>>>>>> >>>>>>> I am using the following link: >>>>>>> https://fedoraproject.org/wiki/Architectures/ARM/F23/Installation >>>>>>> >>>>>>> But there is no comment to write uboot to SD card. >>>>>>> >>>>>>> /usr/share/uboot/odroid-xu3 has two files: >>>>>>> u-boot.dtb >>>>>>> u-boot.bin >>>>>>> >>>>>>> How I should write these files on the final image? >>>>>> We don't support the XU4 on Fedora 23, it is supported on Fedora 24, >>>>>> you should be able to run the 24 RC quite OK on it, I emailed this >>>>>> list about the process a few weeks ago (see list archives) with the >>>>>> details. There's extra steps for the odroid devices as they require >>>>>> binary blobs we can't redistribute. >>>>>> >>>>>> Peter >>>>>> >>>>> Thank you very much for the reply. >>>>> Is there pre built images for Fedora+XU4/3? I appreciate any link >>>>> you may >>>>> know >>>> Yes, the standard Fedora 24 images (choose which one you want) have >>>> support for both the XU3 and XU4. They all have the u-boot and kernel >>>> binaries that are needed. They DO NOT have the binaries I mentioned >>>> before (because we can't legally redistribute them) >>>> >>>> Flash the image you want with arm-image-installer with the >>>> --target=none option plus any others you need. >>>> >>>> You then need to follow the README.odroid to get them binary bits and >>>> flash the Fedora u-boot with it. >>>> >>>> http://git.denx.de/?p=u-boot.git;a=blob_plain;f=doc/README.odroid;hb=HEAD >>>> >>>> >>> README.odroid mentions some files like bl1.bin, tzsw.bin, bl2.bin, >>> ... So i need to build and make "u-boot " project to produce those >>> files? or I can download those files directly? in this case could you >>> please attach the direct links for those files? >>> Thank you very much for your valuable answers and sorry to take up >>> your time >> >> Hi, >> >> You will find all needed information on odroid wiki (chapter >> Installation): >> http://odroid.com/dokuwiki/doku.php?id=en:xu3_building_u-boot >> >> Best regards >> Fabien >> _______________________________________________ >> arm mailing list >> arm@xxxxxxxxxxxxxxxxxxxxxxx >> https://lists.fedoraproject.org/admin/lists/arm@xxxxxxxxxxxxxxxxxxxxxxx > > > Hi there, > > I'm also in the process to bring Fedora to my Odroid XU4. Waht I've done: > > 1. Step > [root@rechner1 ARM]# /usr/bin/arm-image-installer > --image=Fedora-Minimal-armhfp-Rawhide-20160612.n.0-sda.raw.xz > --target=none --media=/dev/sdb -y --addconsole > > ===================================================== > = Selected Image: > = Fedora-Minimal-armhfp-Rawhide-20160612.n.0-sda.raw.xz > = Selected Media : /dev/sdb > = U-Boot Target : none > = Console for none will be added. > ===================================================== > > ***************************************************** > ***************************************************** > ******** WARNING! ALL DATA WILL BE DESTROYED ******** > ***************************************************** > ***************************************************** > = Writing: > = Fedora-Minimal-armhfp-Rawhide-20160612.n.0-sda.raw.xz > = To: /dev/sdb .... > 0+221247 Datensätze ein > 0+221247 Datensätze aus > 2146435072 Bytes (2,1 GB) kopiert, 160,826 s, 13,3 MB/s > = Writing image complete! > = No U-Boot will be installed. > > = Installation Complete! Insert into the none and boot. > > 2. Step > [root@rechner1 U-Boot]# ./sd_fusing.1M.sh /dev/sdb > /dev/sdb reader is identified. > BL1 fusing > 30+1 Datensätze ein > 30+1 Datensätze aus > 15616 Bytes (16 kB) kopiert, 0,86316 s, 18,1 kB/s > BL2 fusing > 28+1 Datensätze ein > 28+1 Datensätze aus > 14592 Bytes (15 kB) kopiert, 0,0811976 s, 180 kB/s > u-boot fusing > 1064+1 Datensätze ein > 1064+1 Datensätze aus > 545023 Bytes (545 kB) kopiert, 1,70465 s, 320 kB/s > TrustZone S/W fusing > 512+0 Datensätze ein > 512+0 Datensätze aus > 262144 Bytes (262 kB) kopiert, 0,968704 s, 271 kB/s > U-boot image is fused successfully. > Eject /dev/sdb and insert it again. > > 3. Step > Boot > > U-Boot 2016.05 (May 19 2016 - 15:01:47 +0000) for ODROID-XU3 > > CPU: Exynos5422 @ 800 MHz > Model: Odroid XU3 based on EXYNOS5422 > Board: Odroid XU3 based on EXYNOS5422 > Type: xu4 > DRAM: 2 GiB > MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1 > *** Warning - bad CRC, using default environment > > In: serial > Out: serial > Err: serial > Net: No ethernet found. > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > starting USB... > USB0: USB EHCI 1.00 > USB1: Register 2000140 NbrPorts 2 > Starting the controller > USB XHCI 1.00 > USB2: Register 2000140 NbrPorts 2 > Starting the controller > USB XHCI 1.00 > scanning bus 0 for devices... 1 USB Device(s) found > scanning bus 1 for devices... 2 USB Device(s) found > scanning bus 2 for devices... 2 USB Device(s) found > scanning usb for ethernet devices... 1 Ethernet Device(s) found > Waiting for Ethernet connection... unable to connect. > BOOTP broadcast 1 > BOOTP broadcast 2 > BOOTP broadcast 3 > > Retry time exceeded; starting again > missing environment variable: pxeuuid > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/00000000 > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0000000 > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/000000 > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/00000 > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0000 > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/000 > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/00 > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/0 > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/default-arm-exynos > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/default-arm > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > missing environment variable: bootfile > Retrieving file: pxelinux.cfg/default > Waiting for Ethernet connection... unable to connect. > *** ERROR: `serverip' not set > Config file not found > Waiting for Ethernet connection... unable to connect. > BOOTP broadcast 1 > BOOTP broadcast 2 > BOOTP broadcast 3 > > Retry time exceeded; starting again > ODROID-XU3 # > > > Why does this board didn't boot the Fedora-Kernel? > > Waht is missing? > > Thanks > Andreas > _______________________________________________ > arm mailing list > arm@xxxxxxxxxxxxxxxxxxxxxxx > https://lists.fedoraproject.org/admin/lists/arm@xxxxxxxxxxxxxxxxxxxxxxx > I saw the following page: http://odroid.com/dokuwiki/doku.php?id=en:xu3_building_u-boot There is a link in that page to download the tool chain to build uboot: http://dn.odroid.com/toolchains/gcc-linaro-arm-linux-gnueabihf-4.7-2013.04-20130415_linux.tar.bz2 When i first executed : arm-linux-gnueabihf-gcc -v There was an error: ld-linux.so.2, no such file or directory Then i made a link named ld-linux.so.2 --> ld-2.15.so This file, ld-2.15.so, is inside the Linaro project and actualy there are 4 files with this name and i tried them all but after executing: arm-linux-gnueabihf-gcc -v The error is that : Accessing a corrupted shared library How to use Linaro and arm-linux-gnueabihf-gcc -v? Please help, thank you. My system is Fedora 20 _______________________________________________ arm mailing list arm@xxxxxxxxxxxxxxxxxxxxxxx https://lists.fedoraproject.org/admin/lists/arm@xxxxxxxxxxxxxxxxxxxxxxx
