|
Objective: boot F21 on MK802II Allwinner A10 headless and without serial console. Installation instructions used were the "manual" ones from: https://fedoraproject.org/wiki/Architectures/ARM/F21/Installation Have applied /usr/share/uboot/Mele_A1000/u-boot-sunxi-with-spl.bin using dd and also tried /usr/share/uboot/Cubieboard/u-boot-sunxi-with-spl.bin I am presuming that this step would have applied sun4i-a10-a1000.dtb or have I missed a step? Have set up wpa on the sdcard before booting using tips from http://wiki.centos.org/HowTos/Laptops/WpaSupplicant with edits of /etc/wpa_supplicant/wpa_supplicant.conf and /etc/sysconfig/network-scripts/ifcfg-wlan0 As well as the various user folders being empty as listed below the messages log file shows that the following Services have failed abrtd firewalld rngd avahi-daemon chronyd sshd-keygen systemd-logind dbus rtkit-daemon ModemManager Any tips on where to start looking? Are there a number of steps to manually do what the firstboot script normally does by writing to the card before booting? I need to have sshd start before login if I am to connect wirelessly - I have no usb ethernet adapter. Thanks -------- Forwarded Message --------
On 15/12/14 16:32, Peter Robinson wrote: > On Mon, Dec 15, 2014 at 5:24 AM, Robert Brown <rebrown@xxxxxxxxxxxxxx> wrote: >> Thanks for the reply Peter. >> >> On 15/12/14 15:58, Peter Robinson wrote: >>> On Mon, Dec 15, 2014 at 4:52 AM, Robert Brown <rebrown@xxxxxxxxxxxxxx> >>> wrote: >>>> Found several log files with date 01/01/1970 (attached). >>>> >>>> /var/log/chrony was empty. >>> Would be until network comes up and chrony can start >>> >>>> Messages log reports: >>>> EXYNOS: PMU not supported and >>>> edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot >>>> edma-dma-engine: probe of edma-dma-engine.0 failed with error -22 >>> All spurious, for HW other than AllWinner >>> >>>> fairly early on. And >>>> >>>> ahci-sunxi 1c18000.sata: PHY power up failed. >>>> ahci-sunxi: probe of 1c18000.sata failed with error -5 >>> Do you have a SATA device attached? >> No sata device attached. >>> >>>> Generated key 1 >>>> Fatal error : getpwnam(chrony) failed >>>> getpwnam(chrony) failed >>>> >>>> A search found all of these were empty: >>>> >>>> /media/rbrown/__/etc/systemd/user >>>> /media/rbrown/__/etc/xdg/systemd/user >>>> /media/rbrown/__/var/kerberos/krb5/user >>>> /media/rbrown/__/usr/share/perl5/User >>>> /media/rbrown/__/usr/lib/systemd/user >>>> /media/rbrown/__/run/user >>>> >>>> First things to check for? >>> Maybe I missed in it earlier posts but what A10 device are you using? >> This is a Rikomagic MK802II hdmi device. Trying to boot headless with no >> serial console! > What uboot are you using, are you specifying a .dtb file, if so what one? > > Peter I have applied /usr/share/uboot/Mele_A1000/u-boot-sunxi-with-spl.bin using dd. This Mele device has shown a very high compatibility previously with the MK802II. Other u-boot options that I could try might be Cubieboard (1) and maybe A10-OLinuXino-Lime but less sure of this last one. Is my understanding correct that this step would have applied sun4i-a10-a1000.dtb or have I missed a step? Rob > _______________________________________________ arm mailing list arm@xxxxxxxxxxxxxxxxxxxxxxx https://admin.fedoraproject.org/mailman/listinfo/arm |
_______________________________________________ arm mailing list arm@xxxxxxxxxxxxxxxxxxxxxxx https://admin.fedoraproject.org/mailman/listinfo/arm
