On 09/05/2014 11:54 AM, Peter Robinson wrote:
On Fri, Sep 5, 2014 at 4:48 PM, Robert Moskowitz <rgm@xxxxxxxxxxxxxxx> wrote:
Still no Ethernet working on my Cubietruck.
Minimal install works fine on mine
# systemctl -l status network.service
systemctl status NetworkManager.service
# systemctl -l status NetworkManager.service
● NetworkManager.service - Network Manager
Loaded: loaded (/usr/lib/systemd/system/NetworkManager.service; enabled)
Active: active (running) since Wed 1969-12-31 19:01:01 EST; 44 years
8 months ago
Main PID: 568 (NetworkManager)
CGroup: /system.slice/NetworkManager.service
└─568 /usr/sbin/NetworkManager --no-daemon
Sep 05 11:43:11 localhost NetworkManager[568]: <info> parsing
/etc/sysconfig/network-scripts/ifcfg-lo ...
Sep 05 11:43:12 localhost NetworkManager[568]: <info> parsing
/etc/sysconfig/network-scripts/ifcfg-lo ...
Sep 05 11:43:13 localhost NetworkManager[568]: <info> parsing
/etc/sysconfig/network-scripts/ifcfg-lo ...
Sep 05 11:43:13 localhost NetworkManager[568]: <info> (lo): link
disconnected
Sep 05 11:43:14 localhost NetworkManager[568]: <info> parsing
/etc/sysconfig/network-scripts/ifcfg-lo ...
Sep 05 11:43:16 localhost NetworkManager[568]: <info> parsing
/etc/sysconfig/network-scripts/ifcfg-lo ...
Sep 05 11:43:17 localhost NetworkManager[568]: <info> parsing
/etc/sysconfig/network-scripts/ifcfg-lo ...
Sep 05 11:43:17 localhost NetworkManager[568]: <info> (lo): link connected
Sep 05 11:43:17 localhost NetworkManager[568]: <info> parsing
/etc/sysconfig/network-scripts/ifcfg-lo ...
Sep 05 11:43:18 localhost NetworkManager[568]: <info> parsing
/etc/sysconfig/network-scripts/ifcfg-lo ...
ip addr
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP group default qlen 1000
link/ether 86:80:43:3c:42:e1 brd ff:ff:ff:ff:ff:ff
ifup eth0
# ifup eth0
/sbin/ifup: configuration for eth0 not found.
Usage: ifup <configuration>
I build the SDcard with:
# /home/rgm/arm/fedora-arm-image-installer/fedora-arm-image-installer.sh
--image=/home/rgm/arm/Fedora-Minimal-armhfp-21-20140905-sda.raw.xz
--target=Cubietruck --media=/dev/sdb --norootpass
Then from the serial console, I set the timezone, root password, and my
user account. Then continue with the boot.
Note that if I build a Fedora 19 SDcard via:
http://docs.cubieboard.org/tutorials/cb2/installation/cb2_fedora_19_card_install,
the ethernet works fine.
_______________________________________________
arm mailing list
arm@xxxxxxxxxxxxxxxxxxxxxxx
https://admin.fedoraproject.org/mailman/listinfo/arm
