I have gone back to the 8/31 build and still no working ethernet on the
Cubietruck. I tried:
ip link set eth0 up
and nothing. Now looking back on my Cubieboard notes, I had ethernet
problems with that, and Hans said, of course, the uboot provided is only
for the Cubietruck, and if I want to work with my Cubieboard2, here is
how to build your own uboot.
So first, why is the ethernet not working? I can put in my F19 SDcard
and boot this system right up with ethernet access. And I have
Cubieboard2 running the F21 code.
And second, I will see if I can build a uboot from the git provided from
Hans for the Cubietruck and see if that gets things working.
On 09/04/2014 12:49 PM, Robert Moskowitz wrote:
Same problem on Fedora-Minimal-armhfp-21-20140901-sda.raw.xz
But a different MAC addr!
Fedora release 21 (Twenty One)
Kernel 3.16.1-301.fc21.armv7hl on an armv7l (ttyS0)
localhost login: root
Password:
[root@localhost ~]# ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP group default qlen 1000
link/ether b6:f8:b8:3c:d5:5f brd ff:ff:ff:ff:ff:ff
I will keep going back to earlier builds and hopefully I will get to
one that brings up eth0.
Um This SHOULD be automatic? I did not have to do it for my F21
testing on the Cubieboard2 or any of my F19 or F20 testing.
On 09/04/2014 11:54 AM, Robert Moskowitz wrote:
On 09/04/2014 11:15 AM, Peter Robinson wrote:
On Thu, Sep 4, 2014 at 3:33 PM, Robert Moskowitz
<rgm@xxxxxxxxxxxxxxx> wrote:
On a Cubietruck -
# yum install policycoreutils-python --nogpgcheck
All packages should now be signed so you can drop the --nogpgcheck
One of the configured repositories failed (Fedora 21 - armhfp),
and yum doesn't have enough cached data to continue. At this
point the only
safe thing yum can do is fail. There are a few ways to work "fix"
this:
Is your date/time correct?
I think it might be worst than date/time. I found the SDcard I was
working with and booted up. No IP addresses on eth0, so no ntp, and
why THAT yum message? Because date/time was essentially ZERO?
I never thought to check on the ethernet. I have only started
working on my 1 Cubietruck, after getting 5 Cubieboard2 systems put
into production. 4 running Redsleeve (with F19 uboot), and 1 F20. I
have run F19 on this Cubietruck with no problems with ethernet. So
something is broken on the Cubietruck uboot support.
Here is what I am seeing on ethernet on the serial console:
[ 36.360611] eth0: device MAC address 56:bb:b8:7a:b2:d6
[ 36.386336] No MAC Management Counters available
[ 36.455808] No MAC Management Counters available
[ 36.473714] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 40.418888] stmmaceth 1c50000.ethernet eth0: Link is Up - 10
0Mbps/Full - flow control off
[ 40.433554] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Last login: Thu Jan 1 00:00:49 on ttyS0
[root@localhost ~]# ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP group default qlen 1000
link/ether 56:bb:b8:7a:b2:d6 brd ff:ff:ff:ff:ff:ff
_______________________________________________
arm mailing list
arm@xxxxxxxxxxxxxxxxxxxxxxx
https://admin.fedoraproject.org/mailman/listinfo/arm
_______________________________________________
arm mailing list
arm@xxxxxxxxxxxxxxxxxxxxxxx
https://admin.fedoraproject.org/mailman/listinfo/arm
