On Wed, Sep 12, 2012 at 2:45 PM, Jon <jdisnard@xxxxxxxxx> wrote: > Hey folks > > was testing kernel-3.6.0-0.rc4.git0.1.fc18 > > Got this: > > dracut Warning: Unable to process initqueue > dracut Warning: /dev/disk/by-label/rootfs does not exist > > > Compared the config: > # # > # Automatically generated file; DO NOT EDIT. # > Automatically generated file; DO NOT EDIT. > # Linux/arm 3.4.2-3.fc17.armv7hl.omap Kernel Configuration | # > Linux/arm 3.6.0-0.rc4.git0.1.fc18.armv7hl.omap Kernel Confi > > . . . > > # # > # MMC/SD/SDIO Card Drivers # > MMC/SD/SDIO Card Drivers > # # > CONFIG_MMC_BLOCK=y | > CONFIG_MMC_BLOCK=m > CONFIG_MMC_BLOCK_MINORS=8 > CONFIG_MMC_BLOCK_MINORS=8 > CONFIG_MMC_BLOCK_BOUNCE=y > CONFIG_MMC_BLOCK_BOUNCE=y > CONFIG_SDIO_UART=m > CONFIG_SDIO_UART=m > # CONFIG_MMC_TEST is not set # > CONFIG_MMC_TEST is not set > > # # > # MMC/SD/SDIO Host Controller Drivers # > MMC/SD/SDIO Host Controller Drivers > # # > CONFIG_MMC_ARMMMCI=m | # > CONFIG_MMC_ARMMMCI is not set > CONFIG_MMC_SDHCI=y | > CONFIG_MMC_SDHCI=m > CONFIG_MMC_SDHCI_PLTFM=m > CONFIG_MMC_SDHCI_PLTFM=m > CONFIG_MMC_SDHCI_PXAV3=m | # > CONFIG_MMC_SDHCI_PXAV3 is not set > CONFIG_MMC_SDHCI_PXAV2=m | # > CONFIG_MMC_SDHCI_PXAV2 is not set > CONFIG_MMC_OMAP=m > CONFIG_MMC_OMAP=m > CONFIG_MMC_OMAP_HS=y | > CONFIG_MMC_OMAP_HS=m > # CONFIG_MMC_DW is not set # > CONFIG_MMC_DW is not set > CONFIG_MMC_VUB300=m > CONFIG_MMC_VUB300=m > # CONFIG_MMC_USHC is not set | > CONFIG_MMC_USHC=m > # CONFIG_MEMSTICK is not set | > CONFIG_MEMSTICK=m > > # > CONFIG_MEMSTICK_DEBUG is not set > > . . . > > Should CONFIG_MMC_BLOCK=y ? > > Also, looks like tegra might have similar problem? > https://fedoraproject.org/wiki/Architectures/ARM/Quality_Assurance/Kernel_Testing#kernel-3.6.0-0.rc4.git0.1.fc18 From: http://jcapik.fedorapeople.org/files/ARM/kernel-tests/kernel-omap-3.6.0-0.rc4.git0.1.fc18.armv7hl-panda+xfce.txt [ 3.577362] omap_hsmmc omap_hsmmc.0: unable to obtain RX DMA engine channel 62 [ 3.585540] omap_hsmmc omap_hsmmc.4: unable to obtain RX DMA engine channel 60 First Enable: CONFIG_DMADEVICES=y then: CONFIG_DMA_OMAP=y The mmc driver was converted to a new dma engine (which also happens to be new in v3.6-rc) in v3.6-rc but it looks as though the KConfig depends wasn't updated... Ran into this last week with the Beagle.. Regards, -- Robert Nelson http://www.rcn-ee.com/ _______________________________________________ arm mailing list arm@xxxxxxxxxxxxxxxxxxxxxxx https://admin.fedoraproject.org/mailman/listinfo/arm
